nemokin Posted November 1, 2015 Share Posted November 1, 2015 HI allI just installed Global Vector and Europe LC on top of already installed Global Base to my Prepar3d v.3I downloaded the latest installer last night, already downloaded Library being the latest.I installed Vector first followed by LC then finishing with the Library install.As instructed during the install, I made sure that FTX is set to Global before proceeding with the install. I do not have any other FTX scenery/texture installed anyway.My Global Base was installed fine as I have made a few flights already in the past week.Something has not properly installed regarding the Vector and LC.Attached are screen grabs at and near LSZR airport in Swiss.AI cars are running over water and field where there are no visible road textures.There are large water areas along the mountain slopes with AI cars again crossing over water.Looking at the scenery file (attached), there are mutiple entries of LC and none for Vector.This looks completely different from the same Global/Vector/LC install I had in my old FSX. Please help me in getting this sorted.Thank you.Kay#FSS0240867 (Global)#FSS0257872 (Vector)#FSS0303269 (OpenLC/Europe) Link to comment Share on other sites More sharing options...
Penzoil3 Posted November 1, 2015 Share Posted November 1, 2015 Have you set Global as the active area in FTX Central since the install ? Your vector entries FYI are way down in the scenery listings- Sue Link to comment Share on other sites More sharing options...
Doug Sawatzky Posted November 1, 2015 Share Posted November 1, 2015 Hi Kay Your scenery library order should look like this... As per page #38 of the FTX Definitive Guide... Scenery Libary Order 3rd Party Scenery (Any scenery you wish to display above Orbx FTX scenery) OZX Scenery (Freeware designed to fit with FTX Regional software) FTX Full Regional Scenery & Airports Tongass Fjords (Fills the gap between Southern Alaska and Pacific Fjords Regions) FTX OpenLC Scenery Named Default Scenery Entries FSGlobal 2010 Entries FTX Global Vector Entries (OBJ, APT, CVX, EXX) Numbered Default Scenery Entries FTX Global Vector Entry (AEC) "Default Scenery" "Default Terrain†Link to comment Share on other sites More sharing options...
nemokin Posted November 1, 2015 Author Share Posted November 1, 2015 Doug, may I ask you to show me the screen grab of the properly sequences scenery library? I have made one flight and one on-going so it is not causing my P3D to crash. Frame rate is fine. I have some water textures pasted at locations that are obviously ground and as I get near them the ground textures get pasted over. I can understand your scenery library order you explained, but I am hoping that seeing your library grab coupled with your written description will have me understand this better. Thank you so much. Link to comment Share on other sites More sharing options...
wedge1047 Posted November 1, 2015 Share Posted November 1, 2015 Hi Kay, The open lc entries need to be moved down the scenery library list, keep them in the same order and moving them down to just below bathymetry in your list should solve your problem. cheers Link to comment Share on other sites More sharing options...
nemokin Posted November 1, 2015 Author Share Posted November 1, 2015 Hi Kay, The open lc entries need to be moved down the scenery library list, keep them in the same order and moving them down to just below bathymetry in your list should solve your problem. cheers Reg Thank you for your trying to help. I moved the LC entried below Bathymetry as you suggested but the problem remains. Water textures appear on mountains, and they get pasted over by the ground textures as I get closer. Also, my default AI cars travel on farmland textures and over these water textures in the mountains. Water textures on mountains are clearly seen in my attached pic, I have red circled the cars traveling on non-roads. I have all the roads turned on in Vector configurator, primary, secondary, and tirtiary. I don't see any roads that Vectore is supposed to provide. I am attaching the pics from the latest attempt as well as my modified scenery library taken from Scenery Config Editor. Link to comment Share on other sites More sharing options...
nemokin Posted November 1, 2015 Author Share Posted November 1, 2015 Hi all, Thank you for all your help! I now have it working OK! It was Sue's comment about activating Global in FTX Central. I had to click "Apply Group" in the FTX Central to activate it despite my having only Global and not any other regions. It now has italicized "active" next to my Global indication. Attached is the same area but with proper mountain textures, more trees I think, and the roads with cars on them. I can even see power lines now that did not exist before. Again, thank you all. Link to comment Share on other sites More sharing options...
Doug Sawatzky Posted November 1, 2015 Share Posted November 1, 2015 Hi Kay Glad to hear things are looking better, you may also want to adjust your "FTX scenery insertion point" within FTX Central as I see your OrbxLibs are at the top of your scenery library, this means that if you install any other FTX Orbx scenery it will install above your 3rd party scenery and everything else again.... http://www.orbxsystems.com/forum/topic/28291-adding-a-scenery-library-insertion-point-ftxcentral-step-by-step/?hl=%2Binsertion+%2Bpoint For your reference, here is what my scenery library looks like.... Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.