active Blurry, Squared textures after P3D v3.4 update

[seery234]

I have recently updated my P3D to V3.4 and took a flight from KLGA to KDEN. While cruising i noticed the ground textures are quite a bit off.

 

Just wondering if this is a known issue and has anyone got any solutions?

 

 

Any help would be great.

 

[erelis]

Hello,

 

Same here. And not only this issue. Missing roads too for example near EDDF  near EYKY and so on. Acctually everithing is meesed up. Cars are driving in amiddle of forests or like in eddm in a middle of a airport etc. Just made fresh installment of p3d v.3.4 and ORBX products: FS Global, Vector (1.30, 1.35.1.40,1.45) and Europe LC and the las install Libraries  and things go wrong now :(. There was no problem with p3d v3.3 at all.

 

please any help.

 

 

[Elaine Dixon]

Seery234,

 

Did you just Update Client ?  Or Client and Content and or Scenery ? 

 

After you Updated.............

 

(1)  Did you Open your FTX Control panel to synchronize your Autogen and Orbx Entries before you started Prepar3D ? 

 

(2) If you Update Scenery,  did you Re-Run the Orbx Global Base Installer again ? (That's a must when you Update Scenery) 

 

(3)  Did you run the Orbx Libraries again ?  (No harm)

 

(4) Did you run the Vector config Tool ?  (if you have it) 

 

(5)  Did you Delete your PreparD.cfg and your Shaders folder after you Updated ?  Right click and Delete both files,  Prepar3D will rebuild them with new settings and Shaders.  You will have to Readjust your Graphics and Scenery settings again,  Start Prepar3D,  go to settings  and re-adjust to your preference 

 

Right Click and delete both files in blue 

 

Location:  Computer ► Local Disk (C:) ► Users ► you ► AppData ► Roaming ► Lockheed Martin ► PreparD v3  Prepar3D.cfg 

 

Location:  Computer ► Local Disk (C:) ► Users ► you ► AppData ► Local ► Lockheed Martin ► Prepar3D v3  Shaders

 

[Elaine Dixon]

16 hours ago, erelis said:

Just made fresh installment of p3d v.3.4 and ORBX products: FS Global, Vector (1.30, 1.35.1.40,1.45) and Europe LC and the las install Libraries  and things go wrong now

 

Erelis,

 

So you Uninstalled Prepar3D V3.3 and then Reinstalled with V3.4 ?  When you Uninstalled V3.3 did you manually Delete the 5 folders,  6 folders Including your Prepar3D Install Location ?   If you didn't you would be overwritten the New folders with the old folders.

 

Did you Uninstall all Orbx products before you Reinstalled Prepar3D v3.4 again ?  Depending of What Default Prepar3D files the Orbx Installer Modifies this might be an Issue for you.  

 

So you have done all the Usual stuff,    Ran Orbx Libraries last ?  Have you run the Vector Airport Elevation Corrections tab (Config Tool) ? 

 

=======================

 

What you could do is this (In this order) 

 

Locate and Delete these items in Blue,  They will Rebuild again with Default files and folder (New) 

 

(1)  Delete this 1 folder and 2 file.. ► Local Disk (C:) ►ProgramData ► Lockheed Martin ► Prepar3D v3  SceneryIndexes  Scenery.cfg  terrain.cfg 

 

(2)  Delete your Prepar3D.cfg...► Local Disk (C:) ► Users ► You ► AppData ► Roaming ► Lockheed Martin ► Prepar3D v3 ►Prepar3D.cfg

 

(3)  Delete your Shaders folder.  ► Local Disk (C:) ► Users ► You ► AppData ► Local ► Lockheed Martin ► Prepar3D v3 ► Shaders 

 

(4)  (Important)  Start Prepar3D,  Then shut it down !   By doing this you will have replaced these deleted files with Default files

 

(5)  Open your FTX Control panel  for a couple of seconds to synchronize\add your Orbx Entries.  

 

Start Prepar3D and see if that helps, (You will have to Readjust your Graphics and Scenery settings again,  Start Prepar3D, Go to settings  and re-adjust to your preference)