jsearl_98 Posted December 3, 2020 Share Posted December 3, 2020 All of a sudden FTX_AU is causing my FSX to hang and I have prevent it from starting (via a dialogue box pop up, or uninstall it.) I have tried re-installing but this has no affect. Any help will be welcome. Thanks John Earl Link to comment Share on other sites More sharing options...
Er!k Posted December 3, 2020 Share Posted December 3, 2020 Hi John, you placed your topic in the wrong section, since this is all about Microsoft Flight Simulator (2020, version XI). Hope one of the moderators will move it into the right place for you. Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 4, 2020 Author Share Posted December 4, 2020 The Forum heading states: FSX support forum?? John Earl Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 4, 2020 Author Share Posted December 4, 2020 My order/transaction ID / receipt number is 5f74cb53d549 for EGHI Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 4, 2020 Author Share Posted December 4, 2020 Sorry, I omitted my order number from my original post. All of a sudden FTX_AU is causing my FSX to hang and I have to prevent it from starting (via a dialogue box pop up, or uninstall it.) I have tried re-installing but this has no affect. Any help will be welcome. My order/transaction ID / receipt number is 5f74cb53d549 for EGHI Thanks John Earl Link to comment Share on other sites More sharing options...
Nick Cooper Posted December 4, 2020 Share Posted December 4, 2020 Hello John, I moved your topic for you. Can you attach a copy of your scenery.cfg file please? Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 5, 2020 Author Share Posted December 5, 2020 scenery.cfg Nick, Config file as requested. I am a bit confused about the forum I posted in. The forum I used was named FSX. Regards John Earl Link to comment Share on other sites More sharing options...
Nick Cooper Posted December 5, 2020 Share Posted December 5, 2020 Hello, thanks. In fact you posted into the Microsoft Flight Simulator forum. That is the new simulator, so I have moved the topic for you into the FSX forum, which is for the older version from 2006. It seems that you have attached the reserve scenery.cfg file. The active one is to be found in C:\programdata\Microsoft\FSX Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 5, 2020 Author Share Posted December 5, 2020 Nick, Sorry about that. Hear is the correct file. Regards John Earl Scenery.CFG Link to comment Share on other sites More sharing options...
Nick Cooper Posted December 5, 2020 Share Posted December 5, 2020 Hello, thanks again. I see that the libraries are not there, nor are there any Orbx products? I assume that your simulator does start using this scenery.cfg file? Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 5, 2020 Author Share Posted December 5, 2020 Yes. I un-installed the Orbx products to avoid the pop-up box appearing telling me there is a problem with FTX_AU. Regards John Earl Link to comment Share on other sites More sharing options...
Nick Cooper Posted December 5, 2020 Share Posted December 5, 2020 Thanks, can you install the Orbx Libraries again? The most common cause is the failure to set the Insertion Point correctly which results in there being scenery library entries below "Default Terrain". In that case, FSX will indeed not start. Please make sure to avoid that and if you see an error message, please take a screen shot of it and attach it to your next post. Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 5, 2020 Author Share Posted December 5, 2020 Ok Nick, Will do. I will have to leave it for a while. I will get back to you when I have done. It will be later today. Regards John Earl Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 5, 2020 Author Share Posted December 5, 2020 Nick, Same result. Here are the files. Regards John Earl Scenery.CFG Link to comment Share on other sites More sharing options...
Nick Cooper Posted December 5, 2020 Share Posted December 5, 2020 Hell, thanks, what happens when you click on Yes? It will not adress objectflow but you should go to the Insertion Point page in Orbx Central and set it so that Airports and Regions is just below Lukla - Mount Everest X - LC, with openLC just below airports and regions. Wait for the blue banner to turn green. Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 5, 2020 Author Share Posted December 5, 2020 I haven't tried that. I am afraid I will corrupt something else. Regards John Earl Link to comment Share on other sites More sharing options...
Nick Cooper Posted December 5, 2020 Share Posted December 5, 2020 Hello, it should remove the error message. It cannot do any harm. Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 5, 2020 Author Share Posted December 5, 2020 Nick, I clicked "yes" and everything seems ok. Any idea why this has suddenly started to happen? Regards John Ear Link to comment Share on other sites More sharing options...
Nick Cooper Posted December 6, 2020 Share Posted December 6, 2020 Hello, probably the entry has been removed from your fsx.cfg file and it is just asking for permission to load the module again. Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 6, 2020 Author Share Posted December 6, 2020 Its a bit annoying! Regards John Earl Link to comment Share on other sites More sharing options...
jsearl_98 Posted December 8, 2020 Author Share Posted December 8, 2020 But thanks for your help! Regards John Earl Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.