Kurtb123 Posted April 16, 2020 Share Posted April 16, 2020 Could you please give me a idea were the vector settings for V5 is, as there is no Vector installation for V5, tx Link to comment Share on other sites More sharing options...
Nick Cooper Posted April 16, 2020 Share Posted April 16, 2020 Hello, Vector is not compatible with P3D v5. This means that 1. it cannot be installed and used 2. if not installed, it cannot be the source of any anomalies, just like any other software that is not installed. Link to comment Share on other sites More sharing options...
Kurtb123 Posted April 16, 2020 Author Share Posted April 16, 2020 Thanks, but how would we correct elevation problems at airports now as in the past by using vector elevation utility? Link to comment Share on other sites More sharing options...
Nick Cooper Posted April 16, 2020 Share Posted April 16, 2020 Hello, you cannot do so using Vector, so you will need to establish what the problem is. Please note that anomalies caused by Vector were typically within the airport boundary. Anything outside is more likely to be either the new default airport of mesh. Which airport and can you show a screen shot of the problem please. Link to comment Share on other sites More sharing options...
Kurtb123 Posted April 16, 2020 Author Share Posted April 16, 2020 FAKN - ZA, open LC AFRICA installed Link to comment Share on other sites More sharing options...
Kurtb123 Posted April 16, 2020 Author Share Posted April 16, 2020 normally the vector utility sorted this out in prp3dv4.5 Link to comment Share on other sites More sharing options...
Nick Cooper Posted April 16, 2020 Share Posted April 16, 2020 Thanks, that is not the kind of problem that Vector could cause. Is that an addon airport? Link to comment Share on other sites More sharing options...
Kurtb123 Posted April 16, 2020 Author Share Posted April 16, 2020 Yes NMG South African scenery. Link to comment Share on other sites More sharing options...
JPL19 Posted April 16, 2020 Share Posted April 16, 2020 May not be related, but, openLCAfrica has an option in the "Configure" Control Panel for "Global Vector corrections" - mine was activated even in v5. Link to comment Share on other sites More sharing options...
Nick Cooper Posted April 16, 2020 Share Posted April 16, 2020 Hello, you could try disabling the open LC Africa mesh. Link to comment Share on other sites More sharing options...
Kurtb123 Posted April 16, 2020 Author Share Posted April 16, 2020 would not like to do that,but lets try, how do i do this Link to comment Share on other sites More sharing options...
Nick Cooper Posted April 16, 2020 Share Posted April 16, 2020 Hello, untick it in the scenery library. If you have installed it into an Orbx Library, it is a different matter. If Vector was curing this problem, how did you make it do so? Link to comment Share on other sites More sharing options...
Kurtb123 Posted April 16, 2020 Author Share Posted April 16, 2020 installed into a library, the vector tool found it automatically as FANS and corrected it Link to comment Share on other sites More sharing options...
Kurtb123 Posted April 16, 2020 Author Share Posted April 16, 2020 cant remember though if that was before install of openLC Africa Link to comment Share on other sites More sharing options...
Nick Cooper Posted April 16, 2020 Share Posted April 16, 2020 Thanks but did you activate or deactivate the Vector AEC? Link to comment Share on other sites More sharing options...
Kurtb123 Posted April 16, 2020 Author Share Posted April 16, 2020 deactivated Link to comment Share on other sites More sharing options...
Nick Cooper Posted April 16, 2020 Share Posted April 16, 2020 Thanks, if so, you were removing Vector and so without Vector should have had the same effect? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.