Jump to content

johnnycrockett

Members
  • Posts

    77
  • Joined

  • Last visited

Everything posted by johnnycrockett

  1. A great quality freeware YBSU Sunshine Coast has already been done by OzX.
  2. Hard to know. If you don't already, you can use Aurasim to calculate landing performance for the Majestic Q400. There is a small fee to subscribe but you can then put in your departure/destination airports and other performance data and it will give you all your V speeds for takeoff and landing along with the margin. Out of curiosity, I used it for ENNK and here is what I got. (113m remaining, bit tight if you ask me!) https://imgur.com/a/EfzmH
  3. The terminals have had significant changes (extensions & overhauls to jetways etc), there is new carparking and the new runway is under construction. The Orbx YBBN is actually pretty good but the airport has just changed a fair bit since then.
  4. I've been using it Jack & so far I'm very happy with it. From what I can tell it hasn't had an impact on FPS or VAS for me but then I haven't been measuring either. I can still complete a flight I could complete before without running into issues while using it if that makes sense.
  5. Hi YSSY, I'm not sure if you are aware but there is currently a great freeware version of YBHM by Anthony Lynch if you are looking for one. It's available on OzX to download. I'm not sure about the others though.
  6. Hi Mohamed, My experience is limited but I will try help as best I can. I recently built a new PC and also got the 7700K. To keep costs low initially I only opted for a CoolerMaster Hyper TX3 Evo, one of the cheaper air coolers around. I intent to change this down the track. Currently my CPU is running at 4.5ghz and temps with my air cooler never exceed 76 degrees - prior to a recent BIOS update they ran a bit higher but are fine now. So to answer your question, if you have happy with temps like that and are planning to get a much better air cooler I think you would be fine as opposed to going liquid cooling.
  7. Great video! Good to see it's going well.
  8. I have SimStarter NG and at startup it allows you to select which simulator (FSX or P3D) you wish to use it with. It is a confusing at first but allows a lot of options which once setup, I've found the sim loads/runs faster.
  9. Feel free to mark this one as solved. Thanks for the help Adam.
  10. Hmm was hoping there might be another way. I will try a reinstall of NZMF & NZQN and see how that goes!
  11. Few hops in Hawaii perhaps? Get the global freeware NA airports that includes a few for Hawaii.
  12. Hi there, I tried a search and couldn't find anything that helped me so apologies for having to post. I have just finished installing NZSI, NZMF & NZQN on a new PC with FTXC3. I have got elevation issues at both NZQN & NZMF (sunken) I have run AEC in Orbx Vector but this hasn't fixed it. I remember from a while back the solution was to run NZSI installer again but wonder if that is still the case with FTXC3? Thanks in advance.
  13. Hi Nick, I installed it into FSX SE. Same issue with no control panel.
  14. Yes I wondered about the control panel too, I haven't been able to find it hunting through the Orbx folder either.
  15. Further to above I have run AEC through Vector and it didn't change anything. Should I manually be exempting this airport in AEC?
  16. Hi there, I recently installed Sekiu airport however I don't seem to have any buildings. All the other autogen is there including trees, peopleflow and the crazy bulls but no hangars etc. I have tried uninstalling and re-installing without any luck. I am also running the latest libraries. Screenshot below. Could this be an elevation issue? Any suggestions? Thank in advance
  17. Thanks Spirit, gave it a try, didn't know I was able to map multiple exe's to the profile however that didn't work, even as an 'absolute'. Thank you for the link though!
  18. The only issue I've noticed so far is that nVidia Inspector doesn't work, I've upgraded to the new one and it works however it lists FSX as MS Flight Simulator 10 and you can't adjust anything with it.
  19. Has there been any news or progress in relation to this?
  20. Sorry to jump on the thread as well but I am also experiencing very bad blurries since migrating. I'm running FSX:SE with both Global products and FTX regions. I have tried the following so far; -Deleted .cfg and let it rebuild and haven't touched it since -Deleted the shaders etc as per Ben's previous instructions -Disabled Flytampa Sydney LC to fix the missing tiles in Sydney city None of this has had any effect on the blurries, they are still really bad. Same symptoms as everyone else here (happens almost straight away, need to pause to let catch up etc etc)
  21. +1 Blurries in FSX. FPS seems to have taken a hit too. Thanks
  22. On the left joystick in the VC there is a hat switch. If you left click and drag down/up accordingly you can activate the trim. This also actuates the aileron trim too so before clicking wait for the tool tip to show up and you will know if it is elevator or aileron. It doesn't stay activated so you will have to repeat depending on how much trim you need.
×
×
  • Create New...